News: If you are a ERCHA member and do not have ERCHA member status in forums please post.
Pages: 1 [2] 3 4 ... 10
 on: September 12, 2015, 10:45:50 AM 
Started by woodchopper - Last post by woodchopper
Hey guys

Its one week until our Fall fun fly. We will have a new item on our lunch menu thanks to master BBQ expert Derek L so come on out for a great weekend of flying, good people and good food!

Long range forecast looks fantastic!

Charge up your batteries, tune up your thumbs add come out and show us your new move!!!!

See next weekend, Sept 18, 19, 20


 on: August 24, 2015, 09:18:27 AM 
Started by Freeskiken - Last post by Freeskiken

Anyone who violates controlled or restricted airspace and endangers the safety of manned aircraft could be subject to fines or administrative penalties up to $25,000 and/or imprisonment.

 on: August 24, 2015, 09:05:55 AM 
Started by Freeskiken - Last post by Freeskiken
Transport Canada issued a Civil Aviation Safety Alert to remind all persons operating unmanned aircraft (model aircraft and unmanned air vehicles or UAVs), for any purpose, about the safety impacts and consequences of interfering with manned aircraft operations, including firefighting aircraft.
This summer, a number of incidents occurred in British Columbia where manned aircraft fighting forest fires were grounded due to interference from unmanned aircraft. The Canadian Aviation Regulations state that no unauthorized person shall operate an aircraft within 5 nautical miles (9 km) of a forest fire or within any associated restricted airspace.
The Civil Aviation Safety Alert is also a reminder of the consequences of contravening regulations pertaining to the use of unmanned aircraft.
Please distribute the Alert or this message where appropriate.
Thank you,

 on: August 21, 2015, 09:57:02 PM 
Started by chop - Last post by woodchopper
First, what is the pack for? if it is primary power on an expensive machine with big current draw you maybe better off to replace the pack.  Second, are you sure its aluminum? if it is it is a challenge to solder at the best of times as it oxidizes rapidly.  It would be a bit odd for the tab to be Al connected to copper wire. 

Let us know what you think and maybe someone can meet with you to give it a try.



 on: August 16, 2015, 12:25:18 PM 
Started by chop - Last post by chop
looking for someone that would be able to help me solder the pos lead back onto my lipo pack . the alum tab broke off and there only a 1/4 '' left to solder too?  Cry
my email is

 on: July 20, 2015, 09:58:15 PM 
Started by woodchopper - Last post by woodchopper
Hey Guys

With the dogged determination of an up stream Salmon Ken has fixed the Diesel  generator. Hopefully it is back to its old self.  The fuel is in the back half of the gen shed.  Please do not boost or charge the generator with the battery hooked up, meaning.... if it wont start walk away.....Wink 

If you have anything but a perfect experience please let us know.


 on: July 03, 2015, 09:39:28 AM 
Started by woodchopper - Last post by woodchopper
Hey all

As most of you know we have set up a Facebook page at   It is a closed group so you need to be a member to see the content.  Past and present members should have received an email with instructions on how to join.  If you haven't received the e-mail or would like access as a non ERCHA member pls pm me or post here.

In spite of my misgivings about the whole "Facebook thing" the page looks and works vary well and is getting lots of traffic from our active members so I will encourage everyone to give it a try.

See you over there!


 on: June 23, 2015, 10:35:19 PM 
Started by woodchopper - Last post by woodchopper
Yea nice pic's Roger!

Thanks to everyone who came out and made it a great event!

And I think we have the album upload feature fixed. Give it a try>


 on: June 22, 2015, 11:04:47 AM 
Started by woodchopper - Last post by Freeskiken
Nice Pictures Roger  Cheesy

 on: June 21, 2015, 08:19:20 PM 
Started by woodchopper - Last post by Freeskiken
Thank you !!! Andre !!! Travis and Mark for figuring out the generator issue. It ran all day and did not stop. GREAT NEWS.

Pages: 1 [2] 3 4 ... 10